The Official Source for Focusrite Product Support and Information .: Focusrite Answerbase

Connecting an Octopre to a Digi 002.
If the optional A/D converter card is fitted then you can use a single ADAT cable to connect from either of the Octopre ADAT outputs to the ADAT in of the 002. Make sure that the bit depth and...
2005-09-24 Views: 8256

Connecting ISA 428 to a Digi 002.
If you have the ADC card installed then you can connect via ADAT optical - connect from either of the ADAT outs on the 428 ADC to the ADAT IN on the 002. This format supports 8 channels of digital...
2005-08-11 Views: 6038

How many inputs and outputs are available at 88.2kHz or 96kHz?
When running at the higher sample rates of 88.2kHz or 96kHz on the Saffire Pro 40, you will lose some ADAT channels. This is standard place when using ADAT, as ADAT only supports the full eight...
2013-03-20 Views: 431

Connecting the ISA 428 with ADC card to a MOTU 896HD.
The 896HD has an ADAT IN port which you can connect one of the ADAT outs of the 428 to. This way all 8 channels of the 428 converter will be transmitted to the 896HD. Note that the 896HD only...
2005-08-10 Views: 4352

Connecting a Liquid Saffire 56 to 2 External Preamps via ADAT
When connecting external preamps to the Liquid Saffire 56 via ADAT, the biggest consideration is how all of the devices are synced together. All digital devices in a signal chain must be synced to...
2011-01-26 Views: 13484

Why doesn't Cubase update my digital connections when switching between sampling rates?
Because Saffire PRO 26 i/o operates in different modes depending on the sampling frequency, it may be necessary to relaunch Cubase when using the ADAT/SMUX connections. At 88.2 kHz or 96 kHz the...
2006-08-23 Views: 3783

ISA 828 ADC ADAT Output Configurations
The ADATTM output connectors operate as follows: 44.1/48kHz sample rates: Connector 1 = channels 1 to 8 in parallel Connector 2 = channels 1 to 8 in parallel (identical to connector 1)...
2007-10-16 Views: 3557

What can I do if I hear clicks and pops or have sync problems with my Octopre?
If your Octopre is not syncing to your sound card/audio interface or vice versa, or you are hearing clicks and pops in your recordings, then:- Ensure that the sample frequency and bit depth...
2005-08-02 Views: 5599

How do I access the digital inputs?
The ADAT and SPDIF digital inputs need to be turned on in SaffireControl PRO before their input mix pages can be accessed. This can be done by hitting the "Enable" button in the sync section of...
2006-09-26 Views: 4127

Standalone mode options.
There are two choices for using the Saffire pro in standalone mode. Tracking Mode will route the analogue inputs to the ADAT outputs, and the ADAT inputs to the analogue outputs. Mixer Mode...
2006-09-26 Views: 7007

How do I set up my ISA One with Pro Tools LE and M-Powered hardware?
Some users wish to use their ISA one preamp with Pro Tools LE or M-Powered by digitally connecting their ISA to the digital inputs of their Pro Tools hardware. This will allow a high quality...
2009-08-24 Views: 10028

I am not sure where the connectors need to go when fitting the ADAT card in my Octopre LE - the instructions do not make it clear. What is the right way?
Check out the updated Installation Instructions for fitting the card. If you still require help then please contact us for further info. This is how the card should look, if installed...
2005-09-26 Views: 3370

Which ADAT optical input port should I use for 44.1 and 48 kHz sample rates?
When the OctoPre Mk II Dynamic is set to 44.1 or 48 kHz sample rates, only the right hand optical input (as you face the back of the unit) will function as an input, contrary to the screen printing...
2010-04-13 Views: 4841

How do I use all 18 inputs on the Scarlett 18i20?
The Scarlett 18i20 may only have 8 analogue channels built into the unit, but you can actually record up to 18 channels simultaneously into your computer. This is as the unit also has two types of...
2013-01-10 Views: 1537

I'm not using the ADATs, can I save on CPU by disabling them?
Yes. There is an option in Saffire Control PRO to disable the ADATs. This is described below. Mac: Go to 'Hardware' in the menu bar and select 'Disable ADATs for better CPU usage' PC: Go to...
2006-09-26 Views: 2772

I am experiencing clicks and pops with my Octopre LE connected using ADAT Lightpipe. What can I do?
If your Octopre LE is not syncing to your sound card/audio interface or vice versa, or you are hearing clicks and pops in your recordings, then:- Ensure that the ADAT cable(s) is not faulty - try...
2005-09-26 Views: 4633

What is the difference between the Octopre and Octopre LE?
Most notable is the pre-amp designs. They are similar in performance but not identical. The original OctoPre is a typical Class A Platinum design, (based around a 737 Rhom transistor) the LE is an...
2005-08-02 Views: 9215

How can I sync up the OctoPre MkII's clock?
There are two synchronisation options available: OctoPre MkII as Clock Source Master: Connect the OctoPre MkII to the digital device via ADAT and ensure that the receiving device is set to...
2009-09-14 Views: 5815

How can I sync my OctoPre MkII Dynamic?
There are a number of synchronisation options available: OctoPre MkII Dynamic as clock source master - ADAT: Connect the OctoPre MkII Dynamic's optical output to the digital device's...
2010-02-10 Views: 4906

Audio connections on the Rednet 3
The Rednet 3 provides a maximum of 32 digital inputs and outputs using the following connections and protocols: - 32 channels of ADAT optical inputs and outputs (16 I/O at 192kHz) via 16 Toslink...
2011-03-17 Views: 1678

I can't see the digital output connectors on the back of my new Octopre. What do I need to get?
The Octopre (and other Platinum units) do not come with digital outputs as standard. You can purchase a digital output card which you can be easily fitted into the unit to give you a digital...
2005-08-03 Views: 3352

Specification comparison chart between the Saffire Pro 10, 26, 24, 40 and the Liquid Saffire 56
Below is a useful chart enabling you to easily compare the Saffire Pro 10 and 26 with the Saffire Pro 40 and the Liquid Saffire 56.
2008-11-24 Views: 20560

What digital options are available for the Octopre LE?
There is only one digital card which can be fitted in the Octopre LE: this gives the unit an 8-channel ADAT Lightpipe input and output. For more information check out the Octopre LE CODEC section...
2005-09-26 Views: 3905

OctoPre Mk II Troubleshooting Guide
No output when using the MIC INPUT • Is the power switched on? • Is the LEVEL set correctly? Most of the gain is applied in the latter stages of the gain dial. Try turning it up further. •...
2009-09-16 Views: 3269

Latency-free monitoring when using 2 Saffire PROs
Although it is not possible to create a single monitor mix from multiple Saffire PROs solely using the Firewire connections (as the Saffire range's latency-free monitoring is achieved by internal...
2007-06-27 Views: 4930

OctoPre MkII Dynamic Troubleshooting guide
No output when using the MIC INPUT • Is the power switched on? • Is the LEVEL set correctly? Most of the gain is applied in the latter stages of the gain dial. Try turning it up further. • For...
2010-02-10 Views: 3542

How good are the ISA 428 optional A/D converters? What are the specs?
We have strived to make the ISA converters to the highest possible quality to preserve the detailed sound of the mic pres after conversion. The 428 converters are a very serious rival to any other...
2005-08-11 Views: 4739

Latency-Free Monitoring In Dual Device Mode
Dual device support is implemented from Saffire Mix Control 1.7 onwards, and allows a user to control 2 interfaces simultaneously with the computer (with the exception of 2 Liquid Saffire 56s, or...
2009-09-10 Views: 5348

How can I synchronise my Rednet 3 with external digital devices?
The Rednet 3 can be used to synchronise your Rednet system clock to external digital audio devices, either via the clock signals embedded in the incoming digital audio streams (ADAT, AES, or...
2011-03-17 Views: 1472

What's the difference between ISA 430 MK I and II?
The 430 and 430 MkII are sonically very similar. The pre-amp, compressor, EQ, gate and de-esser circuits use the same designs. The elements in the MkII which will give a different sonic result are...
2005-08-02 Views: 8745

Configuring the System Output in Dual Device Mode (Mac OS X)
Dual device support is implemented from Saffire Mix Control 1.7 onwards, and allows a user to control 2 interfaces simultaneously with the computer (with the exception of 2 Liquid Saffire 56s, or...
2009-09-10 Views: 5432

Digital Inputs and Sync Source Selection with a Saffire PRO
As of Saffire PRO 2.0, SPDIF and ADAT digital inputs are always 'ON' (unless you have disabled the ADATs for better CPU performance). This means that you no longer have to turn the digital inputs...
2007-07-06 Views: 4912

How do I digitally sync my ISA with other studio gear?
The ISA 220, 428, 430 and 430 MkII can be fitted with optional digital converter cards. If your unit has one of these cards fitted and you are connecting digitally to other equipment (via AES,...
2005-08-02 Views: 6494

ISA 428 Troubleshooting Guide
No LEDs illuminated • Is the POWER switched on? • Is the correct mains voltage being used for your unit? If not, the fuse may blow, requiring the correct fuse to be refitted. (Click here to find...
2009-06-28 Views: 3256

Scarlett 18i6 Troubleshooting Guide
For any problem you may be experiencing, please ensure that you have the latest software for the 8i6 from here. If this doesn't help, see the steps below: My Scarlett isn't powering up The...
2011-05-06 Views: 14437

ISA 430 MKII Troubleshooting guide
No LEDs illuminated • Is the POWER switched on? • Is the correct mains voltage being used for your unit? If not, the fuse may blow, requiring the correct fuse to be refitted. (Click here to find...
2009-06-28 Views: 1783

Guide to Setting up your Studio Part 2
Back To Part 1 | Continue To Part 3 Impedance Issues Some users seem concerned about whether the impedance differences between various inputs and outputs will cause any problems with their...
2005-08-04 Views: 30322

Scarlett MixControl tutorial
Scarlett MixControl is the control software that is used to control the output routing and settings for the Scarlett interface range. This tutorial will explain the features and settings of...
2011-05-06 Views: 22544

Scarlett MixControl tutorial
Scarlett MixControl is the control software that is used to control the output routing and settings for the Scarlett interface range. This tutorial will explain the features and settings of...
2013-03-22 Views: 830

Scarlett MixControl tutorial
Scarlett MixControl is the control software that is used to control the output routing and settings for the Scarlett interface range. This tutorial will explain the features and settings of...
2013-03-22 Views: 834

Search Results

Articles