Focusrite Answerbase - Deutsch
Die offizielle Quelle für schnelle Hilfe und Informationen zu Ihren Focusrite-Produkten
English | German
Glossary Contact Us
Search  
Main Index
 Aktuelle Saffire Baureihe
 Control 2802
 Focusrite/Digidesign
 Forte
 ISA Reihe
 iTrack
 Kompatibilität
 Liquid Reihe
 Manuals und Software
 Platinum Range
 Compounder
 MixMaster
 OctoPre
 OctoPre LE
 Penta
 Platinum Digital Options
 ToneFactory
 TrakMaster
 TrakMaster Pro
 TwinTrak Pro
 VoiceMaster
 VoiceMaster Pro
 Plug-Ins
 Red Range
 Rednet
 Saffire Reihe
 Scarlett USB 2.0 Baureihe
 Technik bezogene Artikel
 VRM Box
Main Index .: Platinum Range .: TwinTrak Pro

TwinTrak Pro

Articles

article I can hear distortion when the compressor on my TwinTrak Pro is set to 'hard ratio'. Is there a problem?
Owing to the optical elements in the compressor circuitry, a certain amount of distortion will occur when a lot of compression is applied. This distortion is also dependant on the type of...
2005-08-10    Views: 2128   
article The LEDs do not illuminate
ï Is the POWER switched on?ï Is the correct mains voltage being used for your unit? If not, the fuse may blow, requiring the correct fuse to be refitted. (See Fuse changing in the GENERIC SETUP)
2005-08-03    Views: 2278   
article There is no sound output from the digital output option.
ï Is the sample frequency set correctly?ï Is the receiving device set to receive at 24 bit?ï Is the receiving device set to external sync? (See DIGITAL in GENERIC SETUP)ï Is the signal format...
2005-08-03    Views: 2652   
article The Digital Card seems to clip before reaching 0dBFS
Have the jumpers been removed from the A/D card? (See A/D card installation for more details)
2005-08-03    Views: 2180   
article My TwinTrak Pro gets very hot whn in use. Is this a problem?
The TTPro gets hot because it uses class A circuitry. The unit is designed to run hot and so the heat is not a problem, even on long sessions, although we do advise to leave space above the unit...
2005-08-09    Views: 2150   
article I cannot hear the DAC signal with the 'digital insert' button switched out on my TwinTrak Pro. What is wrong?
If the digital insert button is pressed in on the TwinTrak Pro then the signal from the DAC is routed to the channel line inputs. If the digital insert button is pressed out then the DAC signal is...
2005-08-09    Views: 1966   
article I can hear hiss and crackling noises on the headphone output of my TwinTrak Pro. What can I do?
Make sure that nothing is connected to the unit, the headphones mix knob is set fully anti-clockwise and all processing is switched out, then listen to the headphone output. Check to see if the...
2005-08-09    Views: 2721   
article I can hear hum when using a dynamic mic with the TwinTrak Pro. It gets louder when I engage the 'air' switch. Is something wrong?
Unfortunately this is inevitable - dynamic mics can be good at inducing hum and the inductor circuit activated by the 'air' switch will only make it more audible. Setting the impedance to maximum...
2005-08-09    Views: 2133   
article What does the input impedance setting on my TwinTrak Pro do? How do I know where to set it?
This setting changes the load seen by the microphone which has an effect on the sound of the signal. Check out the article 'Microphones, pre amps and impedance' by Focusrite's Rob Jones to find...
2005-08-10    Views: 3182   


.: Powered by Lore 1.6.3

Copyright 2009 Focusrite Audio Engineering Ltd. All Rights Reserved.